許多人對電動扭矩扳手螺栓的擰緊操作步驟都不是很分明，在操作的時分都很迷茫，今天鑄衡小編就為大家處理這一難題，下面請看我整理的材料
Many people are not very clear about the tightening operation steps of the bolts of the electric torque wrench. They are confused when they are operating. Today, the small edition of casting and weighing machine handles this problem for you. Now, please see the materials I have arranged.
大家知道電動扭矩扳手螺栓擰緊程序嗎?-http://wrjzzs.com
Do you know the bolt tightening procedure of electric torque wrench? -http://wrjzzs.com
1、裝上反力支架，并緊固螺釘。開動主機，使方頭銷孔與反力支架孔相對應，然后裝入扳手套筒，插上銷釘，并用橡膠圈固定。
1. Install the reaction bracket and fasten the screw. Start the main engine, so that the square head pin hole corresponds to the counterforce support hole, and then install the pulling glove barrel, insert the pin, and fix it with the rubber ring.
2、將控制儀的扭矩旋鈕調到所需扭矩值，將主機正反開關撥到正轉位置，把扳手套筒套在螺紋銜接件的六方上。
2. Set the torque knob of the controller to the required torque value, set the positive and negative switch of the main engine to the positive rotation position, and put the wrench glove barrel on the six sides of the threaded joint.
3、按下電源開關，扳手啟動。當反力支架力臂靠牢支架時（支點能夠是臨近的一只螺栓或其他可作支點的位置）螺栓開端擰緊。當螺栓扭矩到達預定扭矩時，扳手自動中止，緊固完成，松開電源開關，停止下一只螺栓的擰緊工作。
3. Press the power switch and start the wrench. When the reaction bracket arm is firmly attached to the bracket (the fulcrum can be a nearby bolt or other position where it can be used as a fulcrum), the bolt is tightened at the beginning. When the bolt torque reaches the predetermined torque, the wrench automatically stops, the fastening is completed, the power switch is loosened, and the tightening of the next bolt is stopped.
4、扳手自動中止后，靠反力支架的彈性形變力，使支架力臂自動脫離支點，取下扳手。如力臂不能脫離支點時，可撥動正反開關，點動電源開關扳手即可取下。
4. When the wrench stops automatically, the elastic deformation force of the reaction bracket can make the bracket arm break away from the fulcrum automatically and take down the wrench. If the force arm can not be separated from the fulcrum, the positive and negative switch can be switched, and the power switch wrench can be removed by clicking.
For more information, please visit the electric torque wrench website: http://wrjzzs.com
