1 用扳手內套筒*插進螺栓尾部梅花頭部分，同時向前推動扳手，內套筒后退，使外套筒*套住螺母，若不能*套住螺母請左右轉動扳手并向前用力。
1 Insert the inner sleeve * of the wrench into the ring head at the end of the bolt, push the wrench forward at the same time, and the inner sleeve will move backward so that the outer sleeve * can hold the nut. If it can't hold the nut, turn the wrench left and right and force forward.
2 扣動扳手開關，使其旋轉
2 Turn the wrench switch to rotate it
擰斷梅花頭，緊固結束，同時扣動扳機彈出梅花頭
Unscrew the Torx head, tighten it, and pull the trigger to eject the Torx head at the same time
扭剪型電動扳手注意事項：
Precautions for torsion shear type electric wrench:
1 本機所用電源應在本機規定的范圍內，否則會造成機器故障。
1. The power supply used by this machine should be within the range specified by this machine, otherwise it will cause machine failure.
2 不可在雨天或潮濕的環境中使用本機，以免漏電。
2 Do not use this machine in rainy or wet environment to avoid electric leakage.
3 使用本機高空作業時，請系好帶，在操作點下方嚴禁站人及放置貴重物品。
3 When using this machine to work at height, please fasten the safety belt, and it is strictly prohibited to stand and place valuables under the operation point.
使用本機時需遠離易燃易爆物品。
Keep away from flammable and explosive substances when using this machine.
嚴禁破壞電源線及使用電源線拖拉本機。
It is forbidden to damage the power cord and use the power cord to drag the machine.
檢查及維修本機時應先切斷電源。
Cut off the power supply before checking and repairing the machine.
嚴禁過重碰撞本機。
It is strictly forbidden to collide with this machine with excessive weight.
當機器發燙或環境溫度大于35℃時，應停止使用。
When the machine is hot or the ambient temperature is greater than 35 ℃, it should be stopped.
定期檢查碳刷，當碳刷長度小于原長度2/5時，應及時更換。
Check the carbon brush regularly. When the length of the carbon brush is less than 2/5 of the original length, it should be replaced in time.
扭剪型電動扳手檢查與維修：
Inspection and maintenance of torsion shear type electric wrench:
定期檢查電源線，如果有破裂或斷線應及時更換。
Check the power cord regularly and replace it in time if it is broken or broken.
保持內外套筒清潔不得混入雜物。用完本機后應擦拭干凈存放于干燥處。
Keep the inner and outer sleeves clean and free of sundries. After using this machine, wipe it clean and store it in a dry place.
使用前應檢查各緊固螺釘是否松動，如果松動應及時緊固，并試轉聲音是否正常，如果出現異常聲音應及時檢修。
Before use, check whether each fastening screw is loose. If it is loose, tighten it in time, and test whether the sound is normal. If there is abnormal sound, repair it in time.
With the little summary above from the manufacturer of torque wrench, I hope it can help our customers. If you have any questions or need help, please click our website: http://wrjzzs.com Or call for consultation, and we will do our best to solve it for you
